Skymaster Forum  

Go Back   Skymaster Forum > Messages
Register FAQ Members List Calendar Today's Posts

Reply
 
Thread Tools Rate Thread Display Modes
  #1  
Unread 02-08-10, 05:08 PM
edasmus edasmus is offline
Registered User
 
Join Date: Nov 2006
Location: ARR - Aurora, IL - USA
Posts: 434
edasmus is on a distinguished road
Send a message via AIM to edasmus
Hey Scotty....

I checked my POH today and from Section 2 - Systems, page 2-14, the following is exactly as quoted in the POH.



WING FLAP-ELEVATOR TAB INTERCONNECT SYSTEM

"The wing flap system is mechanically interconnected with the elevator trim tab system to automatically eliminate excessive nose-up trim while the wing flaps are being retracted.

With the flaps retracted, the trim control wheel can be rotated in one direction until the trim position indicator reaches the NOSE DN position, or in the opposite direction until it reaches the lower half of the TAKE-OFF range marking for nose-up trim. As the flaps are extended, additional nose-up trim beyond the TAKE-OFF range can be utilized. Maximum nose-up trim is available when the flaps are fully extended. As the flaps are retracted, the interconnect will automatically rotate the trim back to the TAKE-OFF range."



Check your POH and see if you can find any reference to this system. What year and model do you have?

Ed
Reply With Quote
  #2  
Unread 02-15-10, 04:55 PM
edasmus edasmus is offline
Registered User
 
Join Date: Nov 2006
Location: ARR - Aurora, IL - USA
Posts: 434
edasmus is on a distinguished road
Send a message via AIM to edasmus
Scotty,

I managed to do some flying over the weekend as well as today and here are my observations with the elevator trim. I place it in the center or maybe just a touch aft of center of the "TAKE-OFF" range marked on the pointer scale. This makes for a nice easy rotation as the airplane is accelerating through 85-90MPH with flaps at 1/3 extended position. After rotation a slight forward trim is required to hold 110-120MPH on initial climb. Once the airplane is cleaned up some additional forward trim is required to cruise climb between 140-150MPH. All speeds are indicated airspeeds.

During landing, after adding full flaps, the trim pointer is well aft of the "TAKE-OFF" range. Probably a third to half an inch aft of the "TAKE-OFF" range as marked. This is into the additional trim that becomes available with the addition of full flaps. This is at a final approach speed of 90MPH with full flaps making for an easy flare into a smooth touch down with the nose wheel clear of the runway. I can continue to easily hold the nose off for several seconds after main wheel touchdown until the speed bleeds off at which time the nose will gently fall to the runway.

Hopes this helps.

Take-care, Ed
Reply With Quote
  #3  
Unread 02-15-10, 05:37 PM
hharney's Avatar
hharney hharney is offline
Forum Administrator
 
Join Date: Jul 2002
Location: Michigan (8D4)
Posts: 2,276
hharney is on a distinguished road
If you remove the rich Corinthian plastic that Cessna used around the trim pointer you will see that the pointer can be moved and adjusted very easily. You may want to roll the trim to center (check the tab on the elevator) and be sure it is calibrated to about the top of the take-off mark.
__________________
Herb R Harney
1968 337C

Flying the same Skymaster for 47 years
Reply With Quote
  #4  
Unread 02-15-10, 07:13 PM
edasmus edasmus is offline
Registered User
 
Join Date: Nov 2006
Location: ARR - Aurora, IL - USA
Posts: 434
edasmus is on a distinguished road
Send a message via AIM to edasmus
Thanks for the info Herb. Do you think my trim indicator is incorrectly calibrated? It seems that it would be indicating accurately. It points in the center of the take-off range during take-off with maybe just a hint aft of that if no one is in the back seats. The pointer is only well aft of the take-off range during landing which is logical to me because I rolled in substantial nose up trim for the landing. Is yours different?

Thanks Ed
Reply With Quote
  #5  
Unread 02-15-10, 07:14 PM
hharney's Avatar
hharney hharney is offline
Forum Administrator
 
Join Date: Jul 2002
Location: Michigan (8D4)
Posts: 2,276
hharney is on a distinguished road
Sounds correct to me. If it's in the T/O area with those results I would say that it is close enough.
__________________
Herb R Harney
1968 337C

Flying the same Skymaster for 47 years
Reply With Quote
  #6  
Unread 02-15-10, 08:51 PM
Roger's Avatar
Roger Roger is offline
Registered User
 
Join Date: Nov 2005
Location: FL-NY
Posts: 211
Roger is an unknown quantity at this point
Might I just say (and please others correct me) but isn't 90mph on final with full flaps a bit fast for that much flap. I could see it over the numbers, but I've never liked full flaps and a lot of power to "force the plane" down final. It seems so much smoother to be at 1/2 - 2/3rd flaps at 90, and then just shy of the numbers hit the rest of the flap to bleed it to stall speed on touchdown. Thoughts ?
Reply With Quote
  #7  
Unread 02-15-10, 09:51 PM
hharney's Avatar
hharney hharney is offline
Forum Administrator
 
Join Date: Jul 2002
Location: Michigan (8D4)
Posts: 2,276
hharney is on a distinguished road
I think Ed is referring to the approach and ready to land. Not over the fence yet. I use about the same, full flaps at 1/4 mile final and 100 MPH IAS (blue line) and then let start to bleed off. I have full aft trim at this point and once I cross the fence at 85-90 MPH IAS just pull the throttle off and let it sink to the flair. Greases every time. If it is a short field then I will establish an airspeed of 80-85 MPH IAS, with power, full flaps, full aft trim and fly the airplane to the fence then bleed it off. Normally the horn is squawking before I reach the fence but with the stol wing the horn sound pre-maturely.

The POH attached calls for the 90 - 100 like Ed quotes too.
Attached Thumbnails
Click image for larger version

Name:	Snapshot 2010-02-15 21-45-04.jpg
Views:	1448
Size:	133.6 KB
ID:	1052  
__________________
Herb R Harney
1968 337C

Flying the same Skymaster for 47 years
Reply With Quote
Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is Off
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 05:34 PM.


Powered by vBulletin® Version 3.6.9
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.