![]() |
|
Register | FAQ | Members List | Calendar | Today's Posts | Search |
![]() |
|
Thread Tools | Rate Thread | Display Modes |
|
#1
|
||||
|
||||
What all gauges is this unit legally able to replace?
TACH FF Oil Pressure Oil Temp Fuel qty CHTs ???? |
#2
|
|||
|
|||
Rick,
Do you remember if you needed the 20ft cable for those? Also, what fuel sensors do you have with it? Thanks, Tripp |
#3
|
||||
|
||||
I’ve been considering the GI-275 as EIS option from Garmin.
Has anyone done the math on cost for all these to replace all primary functions? GI275 x3 MVP-50 x2 CGR 30P x2 (x3?) EDM 960 Anyone consider CIES fuel senders? |
#4
|
|||
|
|||
Tripp,
I did not order extra length cables with the units. I think I recall asking them about that and their reply was that the cables I need come with the units. I am using the original PennyCap fuel sensors ... I hope! We will be doing the fuel calibration in the next week or two. EI said they should work fine ...
__________________
N337K-FT337GP KLOU |
#5
|
|||
|
|||
Rick,
Do you recall what it cost to have the panel recut to fit the 50's? We are really going back and forth over whether to use 50's or 30's and what the real total cost of each would be. Any pricing info you have would be really helpful. You could email me directly at TXSOCCERREF@GMAIL.COM Thanks, Tripp |
#6
|
|||
|
|||
Thanks to Rick Erwin for sharing his MVP-50 photo.
I'm planning the same installation in the April timeframe. I was investigating JPI EDM900, EMD960, and the CGR-30P. JPI doesn't allow two EDM900 for twins, and for me the EDM960 feels to clutter, plus I wanted to separate my engine monitors for each engine. I considered the CGR-30P, but for a few issues. 1. No STC (it would have to be done with a field approval, not a show stopper). 2. I kept adding up all the gauges I wanted to replace and ended up 1 or 2 short. 3. I didn't see a separation between my aux tanks and main tanks. It seems it was adding up both for a fuel remaining reading. 4. My most important reason was there was gauges on different pages and I didn't see a way to place it in a scan mode between the different pages. I.E. the fuel remaining is on a different page, it seemed I would have to manually toggle through the pages to see it. The MVP-50 has everything I can glace at without any page cycling. Karl |
#7
|
|||
|
|||
You're welcome Karl.
I went through the same considerations myself, then finally zeroing in on the MVP-50P ... it's just so capable. To maximize your installation, it really pays dividends to fully understand ALL its capabilities so you can get it configured with the sensors you want, and the screens laid out just the way you want them. Rick
__________________
N337K-FT337GP KLOU |
#8
|
|||
|
|||
Did the cables sent with your mvp 50 allow you to put the junction box or edc or something like that in various places? Where did you mount it ? I bought the mvps 50s for my plane, is there anything that you wise you would have added or changed if you could reconfigure yours ?
|
#9
|
|||
|
|||
EI Product
We went with the EI Product for the 58C a 73 P version.
We can send all then details we went with going back and fourth with EI if that’s helpful! For Rick do have pics of how the install went in 337K? Any learning curves on the install / post install? Thanks |
#10
|
|||
|
|||
Quote:
__________________
N337K-FT337GP KLOU |
#11
|
|||
|
|||
Quote:
I've had a pleasant experience in working with the folks from EI. They have been very accommodating. After the airplane is flying again, I'll just need to send them the configuration files for them to make a couple of changes, re-install the new files, and I think I'll be done. Rick
__________________
N337K-FT337GP KLOU |
#12
|
|||
|
|||
Mark,
The MVP-50P is a certified replacement for all engine, fuel, and electrical instrumentation. It's not certified for removal of the pressurization instrumentation nor for landing gear position indications, although I've duplicated those original indications in the MVP-50P boxes.
__________________
N337K-FT337GP KLOU |