![]() |
|
Register | FAQ | Members List | Calendar | Search | Today's Posts | Mark Forums Read |
![]() |
|
Thread Tools | Rate Thread | Display Modes |
|
#1
|
||||
|
||||
I keep it between 7 and 8 quarts. In the Hawk XP I used to fly it seemed like if you had more than 8 quarts it would blow it out. Similar motor, different plane.
Is that the range I should run it in or have you guys found a different range to be better? Never thought to ask what level I should run it at. Thoughts?? |
#2
|
||||
|
||||
7 quarts seems to be about max from what I have heard. Typically you would allow it to stabilize and see where it levels off at. My engines like 6 quarts. If I keep the level at 7 it greases things up more. Also depending on how hard you run the engines seems to change the amount blown out. If I run 2500 rpm it will tend to be more grease if I run 2350 rpm it seems to be less.
Also not all dip sticks are stamped correctly. This is retaliative to knowing exactly what you have in the sump but not necessarily where the level stabilizes at. But when you change your oil dump 6 quarts in and let it sit for a little bit then see what the stick says. Remember the filter takes a quart too. When my dip stick says 6 I have dumped 7 quarts in the engine.
__________________
Herb R Harney 1968 337C Flying the same Skymaster for 47 years |
#3
|
||||
|
||||
Thanks for the info! My oil and filters will be here this week and I planned on changing the oil this weekend. I will do exactly what you said below to determine the ACTUAL oil levels. Admittedly the dipsticks are really hard to read. I had to clean them up, use a magnifying glass and flash light to read the markings and then scribe lines at the 6 and 8 quart marks to make them easier to read at a glance glance. Thanks again!!
|
#4
|
|||
|
|||
I too have found that the oil is best around 7 qts on the dipstick, any more and I just wipe it off the belly. I use 8 qts on an oil change. Not sure what others are doing but I am changing the oil every 30+ hours. Use 50W in colder months and 100W in warmer. No multi viscosity. But that is just me.
I did put in the quick drain plugs, they are STC'd and make getting the oil out of the front engine a lot cleaner. Frank |
#5
|
||||
|
||||
May I ask who holds the STC for the front quick drain plug, I need to get myself one.
|
#6
|
||||
|
||||
I did not know that there was a quick drain for the front engine.....was always told the nose wheel is too close
__________________
Herb R Harney 1968 337C Flying the same Skymaster for 47 years |
#7
|
|||
|
|||
Quick Drain Plug
this is the one I have, You need to probe attachment as well, there is a 180 degree and a 90 degree version. This is the link to the part. I use the 180 degree version and a section of radiator hose to just have the oil go directly into drain pan. Now if I could only fin a way to keep the case clean when the oil filter comes off.
https://bogertaviation.com/products/...sa4024nm-valve Frank Last edited by frank.oconnor19 : 04-23-20 at 07:49 AM. |
#8
|
|||
|
|||
I too have found 7 quarts is max, without just blowing it out. It tends to stabilize around 6.
|
#9
|
||||
|
||||
Quote:
Frank, I am going to have to show you my oil filter trick. It works about 90% on the front and 100% on the rear. Ziplock bag technique
__________________
Herb R Harney 1968 337C Flying the same Skymaster for 47 years |
#10
|
||||
|
||||
Frank, Thanks for the link to the quick drain, Just purchased one for the front engine. They were also having a 20% off sale at the time of my purchase. My reason for getting one is to eliminate the constant removal of the drain plug. Keeping exposure low. Thanks again for the heads up.
|
![]() |
Thread Tools | |
Display Modes | Rate This Thread |
|
|