Skymaster Forum  

Go Back   Skymaster Forum > Search Forums
Register FAQ Members List Calendar Search Today's Posts Mark Forums Read

Showing results 1 to 25 of 127
Search took 0.07 seconds.
Search: Posts Made By: SteveG
Forum: Messages 03-09-24, 11:01 AM
Replies: 1
Views: 271
Posted By SteveG
O-2 Tt

Came across the attached article concerning a curiosity within the 337's family history that I had not seen before. Posted here if others may be interested.

Apparently a flying example was never...
Forum: Messages 10-12-23, 09:08 AM
Replies: 19
Views: 22,116
Posted By SteveG
This sounds like you're considering jacking the...

This sounds like you're considering jacking the nose wheel off the ground using only a front jack. IMHO that's a poor idea. The front jack point is primarily used to stabilize the aircraft while...
Forum: Messages 05-27-23, 05:58 PM
Replies: 2
Views: 5,246
Posted By SteveG
Sorry. I read "out of maintenance" as timed out,...

Sorry. I read "out of maintenance" as timed out, not coming out.
Forum: Messages 05-23-23, 07:28 PM
Replies: 2
Views: 5,246
Posted By SteveG
magneto issues

Just when I thought I had experienced yet another unique failure mode I read a very similar story added by our own Mouseketeer "El queso grande" to the thread about a plane down in Montana in which...
Forum: Messages 04-06-23, 10:42 AM
Replies: 10
Views: 6,203
Posted By SteveG
This aircraft just had its registration renewed...

This aircraft just had its registration renewed on 3/21/2023 in the name of Wyoming Valley Air, LLC of Old Forge, Pennsylvania. So it does not seem to be the abandoned, unloved derelict as it might...
Forum: Messages 01-11-23, 10:06 AM
Replies: 4
Views: 4,928
Posted By SteveG
This is not an "inspection" per se but rather a...

This is not an "inspection" per se but rather a replacement of defective parts. The language of the S.B. is not clear but it appears that the affected part numbers were manufactured after 5/20/2019....
Forum: Messages 12-09-22, 12:21 PM
Replies: 4
Views: 4,871
Posted By SteveG
Thanks for the well reasoned reply. Noise is...

Thanks for the well reasoned reply. Noise is certainly one element of the issue. Every time the surface pressure transitions from positive to neutral or negative the affected skin segments will...
Forum: Messages 12-08-22, 07:04 PM
Replies: 4
Views: 4,871
Posted By SteveG
The trailing edge is comprised of a simple flat...

The trailing edge is comprised of a simple flat sheet of 0.018" material folded in half with a 1/16" radius on the bend. A.C. fabricates the part in house on their bending brake.
Forum: Messages 12-08-22, 11:54 AM
Replies: 4
Views: 4,871
Posted By SteveG
consumer report

I have recently found myself in need of a skin repair to the trailing edge of the elevator. It's a long story having to do with a snow plow and a hangar door that I won't go into here. I retained the...
Forum: Messages 10-27-22, 10:16 AM
Replies: 0
Views: 3,166
Posted By SteveG
spicy artwork

AvWeb's picture of the week, an Austrian push-pull. Nice.

https://s30121.pcdn.co/wp-content/uploads/2022/10/Push-Pull-on-the-Move.jpg.webp
Forum: Messages 09-13-22, 01:36 PM
Replies: 11
Views: 6,210
Posted By SteveG
Kim, I appreciate your taking the time to...

Kim, I appreciate your taking the time to consider this situation and for all that you
contribute to this forum. A well reasoned argument is never snarky and would never be
taken as such....
Forum: Messages 09-12-22, 11:58 AM
Replies: 11
Views: 6,210
Posted By SteveG
I briefly considered altering the engine mount...

I briefly considered altering the engine mount spacer but that would change the entire dynafocal geometry. Wasn't willing to go there. A work-around that I do believe has merit is to add a spacer to...
Forum: Messages 09-11-22, 06:59 PM
Replies: 11
Views: 6,210
Posted By SteveG
pictures

Hopefully these photos illustrates the issue graphically. The mount halves are designed to meet using a 0.620" spacer between them but my (our?) spacers are 0.770" thick leaving a 0.150" gap that...
Forum: Messages 09-11-22, 10:55 AM
Replies: 11
Views: 6,210
Posted By SteveG
update

Thanks for the reply Bill. Yes, the work requires some patience but if you only remove one mounting bolt at a time you can maintain the overall alignment and it will go back just as it came out.

In...
Forum: Messages 08-21-22, 08:25 PM
Replies: 11
Views: 6,210
Posted By SteveG
engine shock mount SDR

I recently undertook what at first appeared to be the straight forward task of replacing the rear engine shock mounts on an A model. But, as usual, the job goes south pretty quickly. The problem...
Forum: Messages 06-03-22, 09:21 AM
Replies: 6
Views: 5,814
Posted By SteveG
The position of the master switch should have no...

The position of the master switch should have no bearing on whether the engine runs or not. Or did you mean that you are turning the ignition switch off to stop the engine? If the master switch kills...
Forum: Messages 05-01-22, 10:16 AM
Replies: 13
Views: 8,843
Posted By SteveG
alternate solution

An impact screw driver will also likely solve the problem. Their advantage is that they simultaneously seat the bit into the screw head and apply a torque to the screw. One only needs to break the...
Forum: Recommended Destinations and Fuel Stops 09-27-21, 02:36 PM
Replies: 4
Views: 10,153
Posted By SteveG
https://www.sent-trib.com/news/50-years-of-flying-...

https://www.sent-trib.com/news/50-years-of-flying-high-perrysburg-twp-couple-gets-faa-honor/article_3cd18f72-1880-11ec-af93-cf69e975c63e.html
Forum: Messages 03-15-21, 02:42 PM
Replies: 11
Views: 11,430
Posted By SteveG
PP, If your StikeFinder antenna is already in...

PP,

If your StikeFinder antenna is already in place and not physically obstructing the cargo pod mounting and you're happy with its performance now you might consider leaving well enough alone, at...
Forum: Messages 03-15-21, 11:29 AM
Replies: 11
Views: 11,430
Posted By SteveG
BFGoodrich Stormscope WX950 w/ antenna mounted...

BFGoodrich Stormscope WX950 w/ antenna mounted overhead the pilot's seat.
Forum: Messages 02-01-21, 06:51 PM
Replies: 10
Views: 12,099
Posted By SteveG
A few random additional thoughts on this project...

A few random additional thoughts on this project by someone who has been there and learns everything the hard way, in the hopes that they may be of some value to others working in the same area....
Forum: Messages 01-28-21, 05:53 PM
Replies: 10
Views: 12,099
Posted By SteveG
Hello again fellow masochists, I've been meaning...

Hello again fellow masochists,

I've been meaning to update my experience in this matter for quite some time but Jeff's latest post requires that I take the time to do it now. Sorry Jeff for the...
Forum: Parts Sources 11-23-20, 09:03 AM
Replies: 6
Views: 13,493
Posted By SteveG
Jeff, The only time one can have too much...

Jeff,

The only time one can have too much information is when it's misinformation. Thanks for your time and consideration in creating an extensive post adding to the collective wisdom of this...
Forum: Parts Sources 11-18-20, 07:32 PM
Replies: 6
Views: 13,493
Posted By SteveG
Jeff, Thanks for the response. The Aircraft...

Jeff,

Thanks for the response. The Aircraft Spruce kit is exactly the same thing as the Knots2U kit but a buck less expensive. Any idea why both list C337 as applicable but both specify in bold type...
Forum: Parts Sources 11-18-20, 01:08 PM
Replies: 6
Views: 13,493
Posted By SteveG
On Knots2U's website under Cessna/337/interior...

On Knots2U's website under Cessna/337/interior they list a primer overhaul kit selling 50 cent o-rings for some 3 bucks apiece but the applicability description states in bold type "for non-fuel...
Showing results 1 to 25 of 127

 
Forum Jump

All times are GMT -4. The time now is 06:31 PM.


Powered by vBulletin® Version 3.6.9
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.