Skymaster Forum  

Go Back   Skymaster Forum > Search Forums
Reload this Page Search Results
Register FAQ Members List Calendar Today's Posts

Page 10 of 13 « First < 8 9 10 11 12 > Last »
Showing results 226 to 250 of 305
Search took 0.01 seconds; generated 65 minute(s) ago. Search: Posts Made By: Kim Geyer
Forum: Messages 09-24-07, 01:47 PM
Replies: 9
Views: 30,113
Posted By Kim Geyer
O2 stuff

We send our stuff to HRD oxygen systems 661-295-0670
The bottles we take to our local fire equipment service guys for thier hydrostatic check. When you call HRD go ahead and order the seals for your...
Forum: Messages 08-12-07, 11:24 PM
Replies: 4
Views: 18,439
Posted By Kim Geyer
Have you tried tightening the screws? I did that...

Have you tried tightening the screws? I did that to one on our E model about 3 yrs. ago. Hasn't leaked since Knock on wood!!!
Kim
Forum: Messages 08-11-07, 10:46 PM
Replies: 6
Views: 26,098
Posted By Kim Geyer
You might want to check out what TCM has to say...

You might want to check out what TCM has to say about it http://www.tcmlink.com/pdf2/SB96-11A.pdf
Kim
Forum: Messages 07-03-07, 10:17 PM
Replies: 44
Views: 224,309
Posted By Kim Geyer
From the condition of the cables I've removed...

From the condition of the cables I've removed from our planes, I would change them all at @ 3000 hrs. You have to take them out to inspect them. When removing the cables I found it much easer to...
Forum: Messages 05-16-07, 08:36 AM
Replies: 5
Views: 24,211
Posted By Kim Geyer
I would check the tank vents first. Then I would...

I would check the tank vents first. Then I would have the fuel pressure settings checked. Also check the referance line that runs from the fuel pump to the throttle body, if they leak, it makes the...
Forum: Messages 04-06-07, 11:41 PM
Replies: 2
Views: 22,320
Posted By Kim Geyer
Try going to...

Try going to http://www.tcmlink.com/pdf2/SIL00-7A.pdf We have T337H's and they use 632062-19A1 dip sticks.
Hope it helps
Kim
Forum: Messages 02-10-07, 09:53 AM
Replies: 4
Views: 19,466
Posted By Kim Geyer
It's a T337H. They have about a dozen of them. My...

It's a T337H. They have about a dozen of them. My son was at Camp Anaconda at the Balad airbase, and sent me pictures of these guys flying over.
Forum: Messages 12-13-06, 10:03 PM
Replies: 7
Views: 22,167
Posted By Kim Geyer
The maintenance manual tells you what to use. It...

The maintenance manual tells you what to use. It sez to use prestite 579.6 sealer or 3c-200. Don't think its been made in quit a few years. I would give Cessna a call. I just replaced a window in a...
Forum: Messages 11-06-06, 10:16 AM
Replies: 10
Views: 31,858
Posted By Kim Geyer
Ya'll might try Pearson Air in Olympia Wa.. They...

Ya'll might try Pearson Air in Olympia Wa.. They give a better discount than anyone else. 1-800-562-6374
Forum: Messages 10-12-06, 07:56 PM
Replies: 4
Views: 20,290
Posted By Kim Geyer
I would take the solenoids off and remove the...

I would take the solenoids off and remove the three screws on top, remove the plunger and clean it. I think you will find hyd. fluid has seeped into it and has gotten gummy. Clean everything off with...
Forum: Messages 09-14-06, 01:11 PM
Replies: 11
Views: 33,584
Posted By Kim Geyer
Ernie This AD only applies to mags on those ...

Ernie
This AD only applies to mags on those Lycoming engines listed.
The repetive inspections only apply to to those Lycoming engines listed in the AD. The TCM service bulletin 645 does apply to all...
Forum: Messages 09-13-06, 02:31 PM
Replies: 11
Views: 33,584
Posted By Kim Geyer
Ernie You are right the AD now only applies to...

Ernie
You are right the AD now only applies to those mags installed on lycoming engines. If you read AD 05-12-06 at the begining it sez this AD superceedes AD 96-12-07 that means take the place of.
I...
Forum: Messages 09-13-06, 12:58 PM
Replies: 11
Views: 33,584
Posted By Kim Geyer
Let me tell you I've done the AD a bunch and no...

Let me tell you I've done the AD a bunch and no we don't have to do it anymore. Basically the new AD takes the place of the old one. Although its not required anymore it sure ain't going to hurt...
Forum: Messages 09-13-06, 12:34 PM
Replies: 11
Views: 33,584
Posted By Kim Geyer
Ernie Thats one of the problems with Adlog...

Ernie
Thats one of the problems with Adlog systems. the new AD didn't apply to your aircraft so you didn't get AD 05-12-06 which does superceed 96-12-07.
Kim
Forum: Messages 09-12-06, 11:47 AM
Replies: 11
Views: 33,584
Posted By Kim Geyer
Ernie The AD you are thinking of is AD 96-12-07...

Ernie
The AD you are thinking of is AD 96-12-07 which was superceeded AD 05-12-06 and it no longer applies to bendix / TCM magnetos on Continental engines. But you still have a recomended 500 hr....
Forum: Messages 08-24-06, 03:54 PM
Replies: 7
Views: 23,766
Posted By Kim Geyer
Ernie One of our Skymasters uses Alcor P/N 86255...

Ernie
One of our Skymasters uses Alcor P/N 86255 but it has an Alcor system in it. Look at the probe connection and see which wire is the longest, if it is the yellow one, this is your probe. If it...
Forum: Messages 08-18-06, 04:09 PM
Replies: 5
Views: 30,191
Posted By Kim Geyer
Larry I think we used a 3 HP motor, which is...

Larry
I think we used a 3 HP motor, which is about as big as you can run on a 20 amp circuit. I can't remember the GPM for the pump but it was larger than we needed and was compatiable with Mil...
Forum: Messages 08-03-06, 01:26 AM
Replies: 5
Views: 30,191
Posted By Kim Geyer
We mule we built is just a pump, motor, filter,...

We mule we built is just a pump, motor, filter, and hoses. just disconnect the lines on the fwd firewall hook the mule lines up, make sure they are full of fluid, plug it in and you're ready to go. I...
Forum: Messages 07-29-06, 10:20 AM
Replies: 6
Views: 30,076
Posted By Kim Geyer
Unhappy Just watched a show on the History Channel about...

Just watched a show on the History Channel about the scrap business. They did a segment on the Starship. They said Beech did buy up all they could, but there was one man in Texas that refused to sell...
Forum: Messages 07-20-06, 12:07 AM
Replies: 34
Views: 71,794
Posted By Kim Geyer
Should have read your problem a little better....

Should have read your problem a little better. Might be a bad connection behind the guages there is a long plug that slides on and it may be loose Check the wiring at the box in the overhead.
Kim
Forum: Messages 07-19-06, 11:53 PM
Replies: 34
Views: 71,794
Posted By Kim Geyer
The first place I would look would be to pull the...

The first place I would look would be to pull the wing panels just outboard of the fuselage, the round ones right at the leading edge. In those holes you will find a big white plastic plug . I would...
Forum: Messages 05-15-06, 10:57 PM
Replies: 2
Views: 19,518
Posted By Kim Geyer
Cessna parts dealers can get them, make sure you...

Cessna parts dealers can get them, make sure you tell them rebuilt or overhauled. it will be about 1/3 the price of new. There are several place that will overhaul them. Quality Aircraft Accessories...
Forum: Messages 04-29-06, 04:21 PM
Replies: 5
Views: 24,092
Posted By Kim Geyer
I'm almost sure thats the primer line. If the...

I'm almost sure thats the primer line. If the line broke off at the fitting you should have enough slack to reflair it. We have priced some of those lines from cessna and the price is unreal. We did...
Forum: Messages 03-22-06, 11:31 PM
Replies: 2
Views: 17,094
Posted By Kim Geyer
Ernie Nose gear actuators on a G model arn't too...

Ernie
Nose gear actuators on a G model arn't too hard to do. Just make sure he measures it before he takes it apart. I think the manual gives you the length from the down lock pins to the mounting...
Forum: Messages 02-25-06, 11:08 PM
Replies: 7
Views: 20,820
Posted By Kim Geyer
Roger Where do you keep your plane when in Fla ?

Roger
Where do you keep your plane when in Fla ?
Showing results 226 to 250 of 305
Page 10 of 13 « First < 8 9 10 11 12 > Last »

 
Forum Jump

All times are GMT -4. The time now is 09:11 AM.

Contact Us - Skymaster Owners and Pilots Site - Archive - Top

Powered by vBulletin® Version 3.6.9
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.